Rules and Guidelines
Want to participate in the discussions? Please read our Community Rules and Guidelines. Need some help? Visit Support and Answers.

  • State Not Answered
  • Locked Locked
  • Replies 3 replies
  • Subscribers 9 subscribers
  • Views 281 views
  • Users 0 members are here
Options
You may also be interested in
This discussion is locked.
You cannot post a reply to this discussion. If you have a question start a new discussion

Capacitive Coupling in Domestic Portable ELV/SELV Equipment

wedgwga
I am trying to learn more about members' experience relevant to ELV and SELV equipment/appliances around the domestic environment.  I am also seeking ti find out if the IET has any formal document or guidance for designers or users of such devices - e.g. Apple iPads with metal backs, metal cased portable lamps and the like.  There is quite a bit of discussion about it in various forums outside of ours (and a bit in some of our Wiring Forums, where some members clearly know chapter and verse about causation!).


I have just bought a new metal cases LED reading lamp and experienced a familiar 'vibration to my fingers' when touched or rubbed gently.  This effect has been occasionally familiar to me over the years but I never fully understood what caused it until now!  I communicated with the lamp's designer and manufacturer and he had not encountered it, and was amazed when I told him I measured 79v ac between the case and domestic earth.  I now know this is a capacitive coupling voltage due to the fact that in a lot of such appliances. it has passed tests as ELV/SELV, having no fixed earth.  However, I was curious as to why the designer did not know that this voltage existed on his lamp, when plugged in to the domestic socket - but he assured me the lamp had passed all the required tests and accorded with the relevant BS.


This feeling to the human body or 'effect' seems to range from not noticeable, to strangely frightening for people who don't understand its cause and being involved deeply in electrical safety (and a former member of the IET Health and Safety Policy Advisory Group) in my past career, I felt that consumers should be informed formally about it when designers know it exists.  Also, testing may need to identify a standard for measures to inform or design out. the effect.


My general research about this resulted in the only formal document I could find, from the Lighting Industry Association, which has an short 'Technical Statement' on the effect but only to state that this is a non-injurious sensation. (https://www.thelia.org.uk/store/viewproduct.aspx?id=16854987)


To that end, I will appreciate any feedback on further work suggestions or general experiences.


Thanks, George Wedgwood MIET CEng CFIOSH (Retired)

Parents
  • 0
    Oh, if only one pole of the incoming mains was at near earth potential and we knew which one it was, we could decouple all out lines to that one, rather than to the mid point or the negative of the DC bus.

    Unfortunately, in Europe at least we have to treat live and neutral as equals, and that has been the case for some time.

    Actually the Y capacitor can be greatly reduced or even eliminated, though at the price a slightly larger transformer. Consider the conceptual images of an SMPS below. The red arrows show the unwanted current path for a PELV connection (grounded output). Where class II operation and or a non grounded output is required, then the same 300V p-p square wave in series with the inter-winding capacitance now appears between input and output. So the earth path is reinstated by a capacitor value chosen to be near open circuit at 50Hz, and large enough to do something at the switching frequency.

    One solution is an isolating transformer at 50Hz, forcing the HF path to be a short local loop. However there are few cases where this really helps as the usual  intention of the SMPS is to eliminate the size weight and losses of a transformer .

    The lower pic shows a better fix, with an inter-winding foil, that  may be earthed, neutralled, or connected to the DC bus, that intercepts the current in the inter-winding capacitance, and returns it whence it came without involving the secondary circuits

    Such designs are far quieter for EMC as well. Sadly commercial pressure to keep the transformer cheap tends to drive the design in  the other way.  Once you have a few hundred volts p-p with edge ristimes on the quick bits of perhaps 50ns, so many volts/nsec it is very hard to get the EMC genie back in the bottle without large Ls and Cs.

Reply
  • 0
    Oh, if only one pole of the incoming mains was at near earth potential and we knew which one it was, we could decouple all out lines to that one, rather than to the mid point or the negative of the DC bus.

    Unfortunately, in Europe at least we have to treat live and neutral as equals, and that has been the case for some time.

    Actually the Y capacitor can be greatly reduced or even eliminated, though at the price a slightly larger transformer. Consider the conceptual images of an SMPS below. The red arrows show the unwanted current path for a PELV connection (grounded output). Where class II operation and or a non grounded output is required, then the same 300V p-p square wave in series with the inter-winding capacitance now appears between input and output. So the earth path is reinstated by a capacitor value chosen to be near open circuit at 50Hz, and large enough to do something at the switching frequency.

    One solution is an isolating transformer at 50Hz, forcing the HF path to be a short local loop. However there are few cases where this really helps as the usual  intention of the SMPS is to eliminate the size weight and losses of a transformer .

    The lower pic shows a better fix, with an inter-winding foil, that  may be earthed, neutralled, or connected to the DC bus, that intercepts the current in the inter-winding capacitance, and returns it whence it came without involving the secondary circuits

    Such designs are far quieter for EMC as well. Sadly commercial pressure to keep the transformer cheap tends to drive the design in  the other way.  Once you have a few hundred volts p-p with edge ristimes on the quick bits of perhaps 50ns, so many volts/nsec it is very hard to get the EMC genie back in the bottle without large Ls and Cs.

Children
No Data

Join us to get the best from IET EngX.

Joining EngX lets you personalise your experience so you stay up to date on the topics that interest you, plus you’ll be able to make connections who are looking to collaborate, exchange ideas and more.

Join us Not now

Community Rules & Guidelines